After reading so many fantastic reviews I purchased the Classic model. Before I write what I think are the negative aspects I'll say that it gives a great workout! That is pretty obvious and I don't think that part is arguable. The disappointment began while unpacking. The wood parts were wrapped fairly well and did not have damage but there were several scratches that I had to sand out and re-oil. It appears that they were there before shipping. Putting it together would have been fast and easy- except 2 of the bolts were bent at about 15 degrees and would not fit. I had to wrap with tape and bend with vice grips. After getting it all together the rower worked well for about a week. I started to notice an annoying kind of popping sound from the left rail as the wheels rolled over on each stroke and recovery. It seems the plastic that the wheels ride on is not flat or adhered well to the rail. It isn't very loud but I can hear it well and it gets my attention, spoiling the nice sound of the water. Really disturbing. Support at WaterRower would like a video of the issue. Seems like an obvious issue and could swap out with a rail that is good instead of me trying to make a video of this small sound while moving the seat back and forth. For a $1500 machine the quality control- or lack of it is disturbing. Having to jump through a bunch of hoops because they are too cheap to just send a part is even more so. Perhaps I am being difficult but it is upsetting to have something touted as so great but put together like a $200 piece of junk. Another complaint would be the lack of any back lighting on the monitor. Really cannot see it if the lights are low. Being able to remove the monitor to attach to a PC wouldn't hurt either. While it gives a good workout the rower really suffers from poor manufacturing.
Assembly was challenging. One of the rails could not be attached because the embedded screw in the cross-beam was too crooked to fit into the hole on the rail. I had to place a nut on it to protect the screws and tap until it was true enough cap nut to be attached. The foot board is slightly wider than the top board. I will sand this to match when I reapply the finish. This will need to be done because the wood has a dry, ashy appearance. The wood is beautiful and mostly uniform. This rowing machine is a nice product, but the build quality of the unit I received was disappointing. I felt lucky that the gashes in the carton did not damage the product as the packaging was optimistic. The leading competitor I use at the gym seems to provide slightly more resistance. It is beautiful and useful, but with room for improvement.
No matter the resistance we set or the power we applied, the machine remains sturdy, centered, and even. We amped up the intensity for 2000m sprints and found that the C2 supports consistent effort in a way water resistance can’t. The machine assists in keeping your intensity uniform, because it stores up remaining energy in the spinning flywheel. Comments about the ride feel of both Concept 2s were noticeably brief. As one tester put it, “It’s unremarkable because it’s good,” and leaves you free to focus on the effort you’re putting into your workout.
The water flywheel is comprised of two paddles encased in an enclosed tank of water. As you pull the cable, the paddles move through the water creating resistance. The beauty of this machine is it uses the mass/density of water. The paddles create the drag, so the harder you pull, the more resistance increases. Think about moving your hands through water. The faster you go, the more dense water feels. The slower you go, the less you feel the resistance. And this type of resistance is excellent for your joints. Click here to read the full review.
The WaterRower Club is handcrafted in solid ash and stained for color. The wood was chosen due to its marvelous engineering properties, especially its ability to absorb sound and vibration, which enhances the WaterRower's quiet performance and smooth operation. Ash, like all woods used in the construction of the WaterRower, is a premium hardwood with incredible longevity and dimensional stability. In addition, the wood is harvested from replenishable forests and is hand finished with Danish oil and urethane for protection.
From a fitness perspective, the WaterRower Club works 84 percent of your muscle mass, helping tone and strengthen your muscles while burning far more calories than most other aerobic machines. The exercise is also low impact, as it removes all the body weight from the ankles, knees, and hips, but still moves the limbs and joints through a full range of motion--from completely extended to completely contracted.
This elegant rowing machine builds strength and stamina by closely simulating a real world rowing experience. Its patented Waterflywheel, which moves through actual water, provides a smooth stroke that exercises 84% of your muscle mass evenly and prevents injuries. When not in use, the WaterRower can be stored vertically against a wall. Made in the USA from ethically sourced walnut wood. Assembly required.
Unlike its WaterRower Natural cousin, the WaterRower Club is designed for high-traffic areas, such as commercial gyms, studios, and rehabilitation clinics. Its dual black rails have been styled to prevent scuffing, while the other wood components are finished in an attractive rosewood, which is more resistant to soiling than the Natural model. Other details include four corner wheels on the rails that increase seat stability and reduce the amount of sweat buildup; a frame that flips upright for handy storage; and a weight capacity of up to 1,000 pounds. The WaterRower Club measures 84 by 21 by 22 inches (W x H x D), weighs 117 pounds (with water), and carries a one-year warranty on the frame and components (WaterRower will upgrade the warranty to five years on the frame and three years on the components with the completion of a registration form).
The WaterRower Xeno Müller Signature Edition rowing machine is handcrafted in solid ash and finished with honey oak stain for color. The WaterRower Xeno Müller Signature Edition has been specifically designed in collaboration with US Olympian and single scull record holder Xeno Müller. This special edition rower features a wider 17" handle and lower footrests for an increased range. Another special feature is Xeno\'s signature included on the rails of either side of the rower thus inspiring you to row like an Olympian!
The WaterRower Club is handcrafted from solid Ash wood, finished with a black and rose stain and danish oil. The WaterRower's patented WaterFlywheel has been specifically designed to emulate the dynamics of a boat moving though water and is unsurpassed in its simulation of the physical and physiological benefits of rowing. WaterRower will not provide support or documentation for any product transported outside of the original country of purchase
Rowing has long been recognized as the perfect aerobic pursuit, with naturally smooth and flowing movements that don't tax the joints but do boost the heart rate. Now you can take your rowing experience to the next level with the WaterRower Classic rowing machine. Using the same principles that govern the dynamics of a boat in water, the WaterRower Classic is outfitted with a "water flywheel" that consists of two paddles in an enclosed tank of water that provide smooth, quiet resistance, just like the paddles in an actual body of water. As a result, the machine has no moving parts that can wear out over time (even the recoil belt and pulleys don't require lubricating or maintaining). More significantly, the water tank and flywheel create a self-regulating resistance system that eliminates the need for a motor. As with real rowing, when you paddle faster, the increased drag provides more resistance. When you paddle slower, the resistance is less intense. The only limit to how fast you can row is your strength and your ability to overcome drag. And unlike conventional rowing machines, which tend to be jerky and jarring, the WaterRower Classic is remarkably smooth and fluid.
It’s time for the next Rough Water Clinic! DATE: Saturday, August 11th from 9a-12p at OWRC COST: $95, includes use of club boat REGISTRATION: Sign up on our new registration system Rough Water Clinic Registration ABOUT THE CLINIC: For experienced OWRC rowers the Rough Water Clinic is an exciting step into the wider and wilder part of open water rowing.… Continue Reading
The Classic Rowing Machine is generally quiet for a water resistance machine, but some users believed that it was a little noisy. Like all rowers, whether it’s a flywheel or a waterwheel, there is going to be noise. The more effort that you put into it, the louder it’s going to get. And most find it motivating to hear the water paddles get louder as they burn more calories.
As with any fitness activity, it’s important to exercise with proper technique, however. The big muscles in the legs are where most of the workout action should be. Injury to the lower back can occur from bending too far forward in the row. It’s best to maintain a upright 90 degree angle to the rowing machine’s seat and slider bar. Using the legs for the motion rather than relying as heavily on the back or arms can help reduce the chance of muscle pulls or other related injuries. Always check with a physician before starting any new fitness regimen.
There is some minor maintenance. Because it's made out of wood, which can expand and contract, the bolts need tightening every few months or so. It's easy and takes only a couple of minutes. That, and putting in a fresh water purification tablet every six to twelve months, are about it for regular maintenance. The only problem I've had with the rower (the reason for 4 stars instead of 5) was a squeak that developed after about 6 weeks. It took me some time to determine the source of the squeak, which was a metal bracket connecting the footrest board to the horizontal boards above the drum. I had to partially disassemble the top section and tighten four bolts, but that fixed the problem and it's been quiet ever since.