The WaterRower Club is hand crafted in solid Ash and stained for color. The WaterRower Club has been designed for High Traffic Areas such as Commercial Gyms, Studios, Rehabilitation Clinics, etc. Its Black Rails have been styled to prevent scuffing, other wooden components are finished in an attractive rosewood which are more resistant to soiling than the Natural model. Each machine has been hand finished with Danish Oil and Urethane for protection. Wood has been chosen due to its marvellous engineering properties, primary amongst these is its ability to absorb sound and vibration enhancing the WaterRower's quietness and smoothness of use. Ash, like all woods used in WaterRower construction, is a premium hardwood with incredible longevity and dimensional stability. s For reasons of ecology, all our woods are harvested from replenishable forests.
 The amount of water in the tank simulates the weight of the boat and crew, the more water in the tank the heavier the boat and crew. The standard Calibration Level is Level 17. If the user is lighter in weight, Level 15-16 can be used. If the user is heavier in weight, level 18-19 can be used. The maximum level to fill the tank is Level 19. DO NOT fill above the maximum level – this could void the warranty.
If the machine is to be housed on a wooden floor you will need a mat beneath to reduce vibration and also noise. If space is tight, the hydraulic options are usually the smallest. It's also worth checking your floor can take the weight if you're going for one of the bigger, heavier models. For most, this shouldn't be a problem, if you have any doubts get a surveyor to check as it could be a very expensive mistake!
Rowing has long been recognized as the perfect aerobic pursuit, with naturally smooth and flowing movements that don't tax the joints but do boost the heart rate. Now you can take your rowing experience to the next level with the commercial-quality WaterRower Club rowing machine. Using the same principles that govern the dynamics of a boat in water, the WaterRower Club is outfitted with a "water flywheel" that consists of two paddles in an enclosed tank of water that provide smooth, quiet resistance, just like the paddles in an actual body of water. As a result, the machine has no moving parts that can wear out over time (even the recoil belt and pulleys don't require lubricating or maintaining). More significantly, the water tank and flywheel create a self-regulating resistance system that eliminates the need for a motor. As with real rowing, when you paddle faster, the increased drag provides more resistance. When you paddle slower, the resistance is less intense. The only limit to how fast you can row is your strength and your ability to overcome drag. And unlike conventional rowing machines, which tend to be jerky and jarring, the WaterRower Club is remarkably smooth and fluid.
Don't know why, perhaps due to rising demand and production bandwidth, but be forewarned quality control is an issue. Assembly is easy enough, though have gap where back separator does not fit snugly after tightening nuts as firm as they will go (see pic). No water level sticker on tank received, so had to measure water manually according to calculations (4 gallons). Siphon was not air tight (even though release valve closed firmly), so had to manually pump instead of siphon. S4 monitor only flashes, not working as of yet and now have to take a apart top of unit to figure out why, currently not resolved after verifying connections and looking at simple solutions on website.
Assembly was challenging. One of the rails could not be attached because the embedded screw in the cross-beam was too crooked to fit into the hole on the rail. I had to place a nut on it to protect the screws and tap until it was true enough cap nut to be attached. The foot board is slightly wider than the top board. I will sand this to match when I reapply the finish. This will need to be done because the wood has a dry, ashy appearance. The wood is beautiful and mostly uniform. This rowing machine is a nice product, but the build quality of the unit I received was disappointing. I felt lucky that the gashes in the carton did not damage the product as the packaging was optimistic. The leading competitor I use at the gym seems to provide slightly more resistance. It is beautiful and useful, but with room for improvement.
1.) I keep reading about cracks and leaks that develop in the water tank. WaterRower even offers a tank repair kit for this very issue. It seems to me that this is a design flaw that they refuse to address, instead offering a fix for when it eventually occurs. Have you seen these tanks to eventually leak? I’m surprised they haven’t tried a one-piece tank.
Performance is meaningless if you can’t or don’t want to use the equipment, and that’s why the Wave Water rower was built for comfort and convenience. With a wide, molded seat to accommodate users of all sizes and a padded, textured rowing handle, you can build your strength and endurance in ease. When setting up the rower, the leveling endcaps with a dial ensure stability. After your workout, storing your Wave Water rower is easy – just fold the frame and roll the rower into a closet or corner.
The WaterRower Classic is outfitted with a Series 4 performance monitor that's designed to balance technical sophistication with user-friendliness. The monitor--which includes six information and programming windows, six QuickSelection buttons, and three navigation buttons--displays your workout intensity, stroke rate, heart rate, zone bar, duration, and distance. Plus, the monitor is compatible with an optional heart rate chest strap and receiver, which helps you optimize your workout and achieve your exercise objectives.

There is some minor maintenance. Because it's made out of wood, which can expand and contract, the bolts need tightening every few months or so. It's easy and takes only a couple of minutes. That, and putting in a fresh water purification tablet every six to twelve months, are about it for regular maintenance. The only problem I've had with the rower (the reason for 4 stars instead of 5) was a squeak that developed after about 6 weeks. It took me some time to determine the source of the squeak, which was a metal bracket connecting the footrest board to the horizontal boards above the drum. I had to partially disassemble the top section and tighten four bolts, but that fixed the problem and it's been quiet ever since.
×