After reading so many fantastic reviews I purchased the Classic model. Before I write what I think are the negative aspects I'll say that it gives a great workout! That is pretty obvious and I don't think that part is arguable. The disappointment began while unpacking. The wood parts were wrapped fairly well and did not have damage but there were several scratches that I had to sand out and re-oil. It appears that they were there before shipping. Putting it together would have been fast and easy- except 2 of the bolts were bent at about 15 degrees and would not fit. I had to wrap with tape and bend with vice grips. After getting it all together the rower worked well for about a week. I started to notice an annoying kind of popping sound from the left rail as the wheels rolled over on each stroke and recovery. It seems the plastic that the wheels ride on is not flat or adhered well to the rail. It isn't very loud but I can hear it well and it gets my attention, spoiling the nice sound of the water. Really disturbing. Support at WaterRower would like a video of the issue. Seems like an obvious issue and could swap out with a rail that is good instead of me trying to make a video of this small sound while moving the seat back and forth. For a $1500 machine the quality control- or lack of it is disturbing. Having to jump through a bunch of hoops because they are too cheap to just send a part is even more so. Perhaps I am being difficult but it is upsetting to have something touted as so great but put together like a $200 piece of junk. Another complaint would be the lack of any back lighting on the monitor. Really cannot see it if the lights are low. Being able to remove the monitor to attach to a PC wouldn't hurt either. While it gives a good workout the rower really suffers from poor manufacturing.
One of the major deciding factors between water and air rowers is price. Water rowing machines are often found in higher price ranges with the lowest model going for $700 and the best models starting around $1,100. Air rowers are found in every price range starting at $300 and going as high as $1,000+. The affordability of air rowing machines makes them very popular.
The WaterRower Club is handcrafted in solid ash and stained for color. The wood was chosen due to its marvelous engineering properties, especially its ability to absorb sound and vibration, which enhances the WaterRower's quiet performance and smooth operation. Ash, like all woods used in the construction of the WaterRower, is a premium hardwood with incredible longevity and dimensional stability. In addition, the wood is harvested from replenishable forests and is hand finished with Danish oil and urethane for protection.
There are various air rower or water rower techniques, but the most basic one is by starting at the back stroke, the knees should almost be completely straight prior to squeezing the shoulder blades together. Then you pull its handle to the sternum. The back of your body should naturally stay in its arched position when doing the whole movement. Do not forget to take a record of the distance you have made after every session. Some people even take it as far as uploading their results online and see how they are ranked from other people who are also doing the same. You clean learn more about rowing machine technique on this page.
The WaterRower Classic is hand crafted in solid American Black Walnut. Like all woods, Black Walnut may vary in color from a rich brown to purple-black. Each machine has been hand finished with three coats of Danish Oil giving a deep lustre an warmth to the wood. Wood has been chosen due to its marvellous engineering properties, primary amongst these is its ability to absorb sound and vibration enhancing the WaterRower's quietness and smoothness of use. Black Walnut, like all woods used in WaterRower construction, is a premium hardwood with incredible longevity and dimensional stability. For reasons of ecology, all our woods are harvested from replenishable forests.
It's been nearly 30 years since John Duke, a former Yale University and USA National Team oarsman, set up a small shop in Rhode Island, USA to begin fine-tuning his innovative water-resistant rowing machine. With its beautiful design and unmatched feel, the WaterRower quickly gained a cult-like following of both on-water rowers and fitness enthusiasts that had found their perfect piece of workout equipment. As word spread of the new product that simulated the feel of on-water rowing, WaterRower transitioned from simply a one-off product found within the occasional boathouse to an established brand in both the rowing and fitness world.
Rowing machines were first used in Archaic Greece. Chabrias, an Athenian military general in 4th Century B.C., invented wooden rowing simulators for his inexperienced oarsmen. This enabled them to learn technique and timing before stepping foot on actual water crafts. And it must have worked — Chabrias successfully led numerous naval attacks against the Spartans.
The WaterRower Club is hand crafted in solid Ash and stained for color. The WaterRower Club has been designed for High Traffic Areas such as Commercial Gyms, Studios, Rehabilitation Clinics, etc. Its Black Rails have been styled to prevent scuffing, other wooden components are finished in an attractive rosewood which are more resistant to soiling than the Natural model. Each machine has been hand finished with Danish Oil and Urethane for protection. Wood has been chosen due to its marvellous engineering properties, primary amongst these is its ability to absorb sound and vibration enhancing the WaterRower's quietness and smoothness of use. Ash, like all woods used in WaterRower construction, is a premium hardwood with incredible longevity and dimensional stability. s For reasons of ecology, all our woods are harvested from replenishable forests.
1.) I keep reading about cracks and leaks that develop in the water tank. WaterRower even offers a tank repair kit for this very issue. It seems to me that this is a design flaw that they refuse to address, instead offering a fix for when it eventually occurs. Have you seen these tanks to eventually leak? I’m surprised they haven’t tried a one-piece tank.
The Challenge AR features an advanced computer monitor providing the rower with measurable performance output, an ergonomically designed seat that rides on precision bearings and rollers for absolute smoothness, an upgraded footboard with advanced heel support, and an innovative soft grip handle to eliminate stress on the hands and wrist during the comfortable, but physical workout.
Another negative point for me is the angle of the seat. Unlike the Concept2, it has a slight backward angle, which makes it easier to maintain good form at the end of the stroke. Given that the Waterrower has greater resistance at the catch, it puts more pressure on the lower back at this point making it uncomfortable for people like myself with lumbar spine problems.
Here’s a secret, because the rowing machine provides an intense full body workout, the exercise burns a high amount of calories not only during the actual activity but also for a period after you’ve stopped. This is known as the “after-burn effect”. Essentially, you’ve worked your body so hard that it is forced to keep burning calories and fat even when you’re not rowing. The scientific jargon for this is “excess post-exercise oxygen consumption” or “EPOC” for short. But all you need to know is that if you’re doing an intense rowing workout, the benefits continue after you’re done. How great is that?
There is much to love about the WaterRower--and I do love it--but I would echo others' comments that although the seat rolls solidly and smoothly on the wood rails, the seat itself is very hard (I use a gel seat pad I bought for my hard fiberglass kayak seat), and the footpads are in need up rethinking and upgrading--the cheap plastic doesn't let you row in socks or barefoot and is not really worthy of a machine that is otherwise a stunning piece of engineering and a beautiful one as well. As one other person noted about his machine, my machine made a clicking noise on the return stroke, so I had to adjust the wheel underneath the top rail that connects to the footpad and pull it away gently from where it was rubbing against another component. Also, be warned: the instruction booklet is in the DVD case. I did not see the little sticker on the case telling me that, thinking I'd wait to watch the DVD until after I'd assembled it. But WaterRower has a copy of the assembly instructions on their website, along with a video (I found the written ones better and easier to follow), so I was able to assemble it with no difficulty.