After reading so many fantastic reviews I purchased the Classic model. Before I write what I think are the negative aspects I'll say that it gives a great workout! That is pretty obvious and I don't think that part is arguable. The disappointment began while unpacking. The wood parts were wrapped fairly well and did not have damage but there were several scratches that I had to sand out and re-oil. It appears that they were there before shipping. Putting it together would have been fast and easy- except 2 of the bolts were bent at about 15 degrees and would not fit. I had to wrap with tape and bend with vice grips. After getting it all together the rower worked well for about a week. I started to notice an annoying kind of popping sound from the left rail as the wheels rolled over on each stroke and recovery. It seems the plastic that the wheels ride on is not flat or adhered well to the rail. It isn't very loud but I can hear it well and it gets my attention, spoiling the nice sound of the water. Really disturbing. Support at WaterRower would like a video of the issue. Seems like an obvious issue and could swap out with a rail that is good instead of me trying to make a video of this small sound while moving the seat back and forth. For a $1500 machine the quality control- or lack of it is disturbing. Having to jump through a bunch of hoops because they are too cheap to just send a part is even more so. Perhaps I am being difficult but it is upsetting to have something touted as so great but put together like a $200 piece of junk. Another complaint would be the lack of any back lighting on the monitor. Really cannot see it if the lights are low. Being able to remove the monitor to attach to a PC wouldn't hurt either. While it gives a good workout the rower really suffers from poor manufacturing.
The Classic Rowing Machine is designed is extremely easy to use. Additionally, it has a lot of comfort features in its design. It has an ergonomically shaped handle and padded heel rests that accommodate nearly everyone. Everything on the machine can be adjusted quickly. Because there are no movement parts, maintenance is minimal. Even the computer has a lot of one button operations, so the minute you have the rower assembled, you can get to work.
A 125-pound person moving at an average pace for 30 minutes on a treadmill will burn roughly 250 calories. However, they aren’t able to take advantage of this after-burn effect. The same person rowing vigorously will burn around to 250 calories but will have less stress placed upon their joints and continue to burn calories after the workout has ended. Rowing machines have been shown to burn on average 800 calories an hour if you work harder and are slightly heavier.
The WaterRower Natural rowing machine is handcrafted in solid ash wood, stained Honey Oak, and finished with Danish oil. Wood is an excellent material for this application due to its ability to absorb sound and vibration enhancing the WaterRower's smooth, quiet operation. The Natural, as with all WaterRowers, features patented WaterFlywheel technology, unrivaled in its replication of the resistance felt in on the water rowing.
One of the major deciding factors between water and air rowers is price. Water rowing machines are often found in higher price ranges with the lowest model going for $700 and the best models starting around $1,100. Air rowers are found in every price range starting at $300 and going as high as $1,000+. The affordability of air rowing machines makes them very popular.
From a fitness perspective, the WaterRower Classic works 84 percent of your muscle mass, helping tone and strengthen your muscles while burning far more calories than most other aerobic machines. The exercise is also low impact, as it removes all the body weight from the ankles, knees, and hips, but still moves the limbs and joints through a full range of motion--from completely extended to completely contracted.
Assembly was challenging. One of the rails could not be attached because the embedded screw in the cross-beam was too crooked to fit into the hole on the rail. I had to place a nut on it to protect the screws and tap until it was true enough cap nut to be attached. The foot board is slightly wider than the top board. I will sand this to match when I reapply the finish. This will need to be done because the wood has a dry, ashy appearance. The wood is beautiful and mostly uniform. This rowing machine is a nice product, but the build quality of the unit I received was disappointing. I felt lucky that the gashes in the carton did not damage the product as the packaging was optimistic. The leading competitor I use at the gym seems to provide slightly more resistance. It is beautiful and useful, but with room for improvement.
Being able to easily store your rower is a huge plus. Make sure you investigate how well the machine stores, if it folds up or comes apart easily to be able to put it in your closet, or in other storage areas. As an example, the Concept2 Model D rowing machine folds up nicely by a simple pull pin located in the middle of the rower. Wheels on the bottom allow for easy moving.
The water flywheel is comprised of two paddles encased in an enclosed tank of water. As you pull the cable, the paddles move through the water creating resistance. The beauty of this machine is it uses the mass/density of water. The paddles create the drag, so the harder you pull, the more resistance increases. Think about moving your hands through water. The faster you go, the more dense water feels. The slower you go, the less you feel the resistance. And this type of resistance is excellent for your joints. Click here to read the full review.
Award Winning Design - The WaterRower has been designed to set it apart from other fitness equipment, featuring an attention to detail unseen in other exercise equipment. Refined Design - The WaterRower has been designed to set it apart from other fitness equipment, featuring an attention to design refinement unseen in other exercise equipment. Hand Crafting - WaterRower’s wooden models are handcrafted from a selection of the world’s finest hard woods (Ash, Cherry, Walnut, Beech and Oak).. Each model is hand finished and coated with Danish oil giving it a deep penetrating Luster. Sustainable & Eco-Friendly - All WaterRower's wooden models are crafted from the finest Appalachian hardwoods sourced only from replenishable forests.
The Water Rower comes partly preassembled in two large boxes. The assembly instructions are reasonably good, and as long as you take your time and follow them carefully (read all the text) it takes about 45 minutes from opening the first box to trying it out. I bought bottles of distilled water to fill it, which made it easy to fill using the included funnel & hose.