After reading so many fantastic reviews I purchased the Classic model. Before I write what I think are the negative aspects I'll say that it gives a great workout! That is pretty obvious and I don't think that part is arguable. The disappointment began while unpacking. The wood parts were wrapped fairly well and did not have damage but there were several scratches that I had to sand out and re-oil. It appears that they were there before shipping. Putting it together would have been fast and easy- except 2 of the bolts were bent at about 15 degrees and would not fit. I had to wrap with tape and bend with vice grips. After getting it all together the rower worked well for about a week. I started to notice an annoying kind of popping sound from the left rail as the wheels rolled over on each stroke and recovery. It seems the plastic that the wheels ride on is not flat or adhered well to the rail. It isn't very loud but I can hear it well and it gets my attention, spoiling the nice sound of the water. Really disturbing. Support at WaterRower would like a video of the issue. Seems like an obvious issue and could swap out with a rail that is good instead of me trying to make a video of this small sound while moving the seat back and forth. For a $1500 machine the quality control- or lack of it is disturbing. Having to jump through a bunch of hoops because they are too cheap to just send a part is even more so. Perhaps I am being difficult but it is upsetting to have something touted as so great but put together like a $200 piece of junk. Another complaint would be the lack of any back lighting on the monitor. Really cannot see it if the lights are low. Being able to remove the monitor to attach to a PC wouldn't hurt either. While it gives a good workout the rower really suffers from poor manufacturing.
On theme with C2’s interchangeability, models D or E are essentially the same machine. When we talk about one we’re talking about both. The Concept 2 E is just 8 pounds heavier but is made out of stronger stuff all around — what’s plastic on the model D is aluminium on the model E, and what’s aluminum on the model D is welded steel on the model E. The only noticeable variations are seat height and display position.
Assembly was challenging. One of the rails could not be attached because the embedded screw in the cross-beam was too crooked to fit into the hole on the rail. I had to place a nut on it to protect the screws and tap until it was true enough cap nut to be attached. The foot board is slightly wider than the top board. I will sand this to match when I reapply the finish. This will need to be done because the wood has a dry, ashy appearance. The wood is beautiful and mostly uniform. This rowing machine is a nice product, but the build quality of the unit I received was disappointing. I felt lucky that the gashes in the carton did not damage the product as the packaging was optimistic. The leading competitor I use at the gym seems to provide slightly more resistance. It is beautiful and useful, but with room for improvement.
The Classic Rowing Machine is generally quiet for a water resistance machine, but some users believed that it was a little noisy. Like all rowers, whether it’s a flywheel or a waterwheel, there is going to be noise. The more effort that you put into it, the louder it’s going to get. And most find it motivating to hear the water paddles get louder as they burn more calories.
From a fitness perspective, the WaterRower Classic works 84 percent of your muscle mass, helping tone and strengthen your muscles while burning far more calories than most other aerobic machines. The exercise is also low impact, as it removes all the body weight from the ankles, knees, and hips, but still moves the limbs and joints through a full range of motion--from completely extended to completely contracted.
The WaterRower Natural is handcrafted in solid ash and stained honey oak for consistency of color. The wood was chosen due to its marvelous engineering properties, especially its ability to absorb sound and vibration, which enhances the WaterRower's quiet performance and smooth operation. Ash, like all woods used in the construction of the WaterRower, is a premium hardwood with incredible longevity and dimensional stability. In addition, the wood is harvested from replenishable forests and is hand finished with Danish oil to provide a deep luster.
×