Note: Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion on limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Rowing machines were first used in Archaic Greece. Chabrias, an Athenian military general in 4th Century B.C., invented wooden rowing simulators for his inexperienced oarsmen. This enabled them to learn technique and timing before stepping foot on actual water crafts. And it must have worked — Chabrias successfully led numerous naval attacks against the Spartans.

The Classic Rowing Machine is generally quiet for a water resistance machine, but some users believed that it was a little noisy. Like all rowers, whether it’s a flywheel or a waterwheel, there is going to be noise. The more effort that you put into it, the louder it’s going to get. And most find it motivating to hear the water paddles get louder as they burn more calories.

Unlike the 1445, the Elite Wave Water Rowing Machine includes an upgraded, high-end fitness monitor and a chest strap heart rate sensor. Programmed to sync seamlessly with the multi-function monitor, the data the sensor provides allows you to tailor your workout. For example, you can target a certain heart rate for weight loss or to increase endurance by adjusting your rowing speed and therefore, your rowing intensity. In addition to pulse, the multi-function monitor also tracks distance, time, calories burned, stroke count and strokes per minute to further motivate you during your rowing session. For further customization, users can also add or remove water using the included siphon to either increase or decrease the resistance.
After reading so many fantastic reviews I purchased the Classic model. Before I write what I think are the negative aspects I'll say that it gives a great workout! That is pretty obvious and I don't think that part is arguable. The disappointment began while unpacking. The wood parts were wrapped fairly well and did not have damage but there were several scratches that I had to sand out and re-oil. It appears that they were there before shipping. Putting it together would have been fast and easy- except 2 of the bolts were bent at about 15 degrees and would not fit. I had to wrap with tape and bend with vice grips. After getting it all together the rower worked well for about a week. I started to notice an annoying kind of popping sound from the left rail as the wheels rolled over on each stroke and recovery. It seems the plastic that the wheels ride on is not flat or adhered well to the rail. It isn't very loud but I can hear it well and it gets my attention, spoiling the nice sound of the water. Really disturbing. Support at WaterRower would like a video of the issue. Seems like an obvious issue and could swap out with a rail that is good instead of me trying to make a video of this small sound while moving the seat back and forth. For a $1500 machine the quality control- or lack of it is disturbing. Having to jump through a bunch of hoops because they are too cheap to just send a part is even more so. Perhaps I am being difficult but it is upsetting to have something touted as so great but put together like a $200 piece of junk. Another complaint would be the lack of any back lighting on the monitor. Really cannot see it if the lights are low. Being able to remove the monitor to attach to a PC wouldn't hurt either. While it gives a good workout the rower really suffers from poor manufacturing.
Assembly was challenging. One of the rails could not be attached because the embedded screw in the cross-beam was too crooked to fit into the hole on the rail. I had to place a nut on it to protect the screws and tap until it was true enough cap nut to be attached. The foot board is slightly wider than the top board. I will sand this to match when I reapply the finish. This will need to be done because the wood has a dry, ashy appearance. The wood is beautiful and mostly uniform. This rowing machine is a nice product, but the build quality of the unit I received was disappointing. I felt lucky that the gashes in the carton did not damage the product as the packaging was optimistic. The leading competitor I use at the gym seems to provide slightly more resistance. It is beautiful and useful, but with room for improvement.
However, I own an air rower and have zero worries about maxing out it’s ability. I can completely exhaust myself on any type of workout. Air and water rowers are the chosen resistance type by Olympic athletes and any athlete looking to train their full-body cardio. I don’t think they would choose this resistance type if they felt they could max it out.

The Waterrower has recently been made famous by Kevin Spacy as the rowing machine used in the ‘House of Cards’. It is a type of wooden rowing machine produced and manufactured by Waterrower Inc. in New England, USA. The rowers were designed by ex-US national team rower john Duke in the mid 1980’s and the company to manufacture them was established in 1988.
Products listed as Out of Stock are currently not in stock at the store(s) being viewed. Note that in some instances, very limited inventory may be available in stores, but because of small quantities we are unable to reflect the availability online. Please remember to check back – if or when inventory is replenished and available, this will be reflected online.
There is some minor maintenance. Because it's made out of wood, which can expand and contract, the bolts need tightening every few months or so. It's easy and takes only a couple of minutes. That, and putting in a fresh water purification tablet every six to twelve months, are about it for regular maintenance. The only problem I've had with the rower (the reason for 4 stars instead of 5) was a squeak that developed after about 6 weeks. It took me some time to determine the source of the squeak, which was a metal bracket connecting the footrest board to the horizontal boards above the drum. I had to partially disassemble the top section and tighten four bolts, but that fixed the problem and it's been quiet ever since.
×